LYNCH ABBEY STRIP LYNCH AUDIO LAB — PRIVATE USER GUIDE 0.2.0 TG transistor and REDD 17,37,51 valve-inspired console paths. These are original Lynch algorithms and visual interpretations, not measured hardware replicas. QUICK START Choose TG or REDD. PRESETS displays only the selected console's Instrument > Use > Sound folders:25 TG and30 REDD starting points. Each sound is individually voiced. INIT stays in the selected console and restores neutral, latency-aligned audio. Loading a User file restores its complete saved console and settings. The host's factory list retains the full bank and stable indices. DETAILS / USER gives every parameter its exact value, plus Save and User loading. The first17 factory indices and all28 parameter IDs are preserved. DRIVE / PREAMP The PREAMP ON/OFF button is now visible on both main panels. Turn Drive above zero with the mouse to enable the preamp automatically. Host automation keeps Drive and Preamp as separate, explicit parameters: automate Preamp ON when automating saturation. Turning the preamp off bypasses coloration completely, even with a nonzero Drive value. Neutral Init starts with it off. There is no hidden continuously moving level matcher. Drive spans0..30dB and changes harmonic saturation, with partial fixed drive compensation. Headroom changes the operating point. Higher Drive is not simply an output fader and does not guarantee constant loudness. Use Output L/R for manual trim. Permanent value readouts show exact Drive, Bass/Spread and mode settings; the printed generated panel legends are visual references. TG EQ AND DYNAMICS The visible EQ enable affects Bass,Treble and Presence together. Bass is a broad low shelf centered at50Hz, ±10dB; it shapes deep bass more than low mids. Treble boost is a broad5kHz bell; cut is a10kHz high shelf. Presence has separate gain/frequency controls. These are published-style tonal concepts implemented with original filter code, not circuit-calibrated curves. Drag or click the physical OUT / COMP / LIMIT lever directly to one of three detents. OUT bypasses dynamics; COMP uses the feedback compressor; LIMIT increases its ratio. Hold sets a minimum attenuation floor, not a time or conventional threshold. Recovery selects100/250/500/1000/2000/5000ms. Dynamics Mix blends only compression within the wet strip, independently of global Wet Mix. SC HP removes low frequencies from the compressor detector at90Hz, not from the audible signal. It therefore changes compression only when the detector is receiving enough low-frequency energy; it does nothing in OUT. Three routing choices place dynamics before EQ, between tone/presence, or after both. Routing affects compression of equalized signals. REDD The AMP physical switch selects17 /37 /51.17 has stronger valve color;37 is denser;51 is cleaner. Drive remains available in every profile. Bass/Treble and Bass Lift belong to its tone section. Classic/Pop changes the REDD37/51 treble boost from shelf to bell;17 keeps shelf behavior. REDD has no TG dynamics, so related controls are inactive in Details. SPREAD 0%=mono,100%=unchanged stereo.100..200% adds a complementary phase-based side signal and also works with a mono input when loaded mono-to-stereo. Its L+R fold-down preserves the center signal. A mono-output instance cannot reproduce width. MONO / WIDE switches between0% and160%; the Spread knob sets any intermediate value. Stereo widening can increase individual-channel peaks; check output headroom. ANALOG NOISE TG NOISE switches Off /70%; Details offers0..100%. REDD has its own continuous noise knob linked to the same parameter. This is optional hiss with a small50Hz hum, made audible at useful levels and normalized for its oversampled noise filter. Zero produces no generated noise. Bypass and global Dry exclude it. Stored nonzero Noise amounts are louder than in0.1.3; adjust by ear. METERS Left and right are independent300ms power/RMS meters. Meter in Details selects Input,Output,or TG gain reduction. Input and Output now use their own per-channel measurements, including in-place rendering. The main panel displays the selected meter mode.0VU=-18dBFS RMS; +3VU=-15dBFS RMS. A sine's sample peak is about3dB above its RMS. This analog-style +3 is not a claim that digital audio can exceed full scale safely. The needle now reaches each printed scale mark through +3. Values beyond the meter's endpoints remain at the corresponding stop. In GR mode0VU means no attenuation; reduction moves left. REDD has no dynamics and shows no TG reduction. OUTPUT / MIX / BYPASS Input,Output L/R and global Wet Mix are manual controls.0% Wet Mix and Bypass reproduce the exact original input delayed by the reported96sample latency; all wet processing is excluded.50% is an aligned linear blend of original input and the whole strip. Sample Protect is optional sample peak protection, not a true-peak mastering limiter. Output can exceed full scale when it is off. Output R's trim is independent of L. Both main faders have calibrated value/position mappings: the black cap center line sits on the printed0dB mark at0dB. Permanent L/R value readouts remove ambiguity. CONTROLS / USER SOUNDS Drag knobs vertically; Shift gives fine movement. Double-click resets. Physical switches support direct click/drag detents. Right-click gives reset and host automation guidance. Hover alone never changes parameters. ? enables contextual explanations. Guide opens in front inside the editor; Escape closes Guide or Details. Six UI sizes are available. User sounds are saved as complete parameter states; the model and shared parameters are retained in the file. VERIFICATION / LIMITS Private macOS arm64 AUv2, stable aufx/Ab01/LyPl identity. Automated engine and actual native AU/editor tests cover five rates44.1/48/88.2/96/192kHz, mono/mono-to-stereo/stereo, state, automation, buffers, dry/bypass, drive harmonics, EQ, dynamics detector, stereo fold-down, noise, VU, switches and menu filtering. No Goldbaby samples or vendor DSP code are included. Actual Logic listening remains a separate check. No claim of certified hardware equivalence or musical world leadership is made. RELEASE AUDIT REFINEMENTS — 15 OCTOBER 2026 TG and REDD can both save complete user presets from DETAILS / USER > Save…. Files must contain a named, valid preset for this plugin. Malformed or oversized files are rejected before any setting changes. Legacy valid presets remain readable. Interrupted mouse/scroll gestures finish when another dial takes over. The output peak display now has the same release time in mono and stereo; this metering correction does not change the processed audio.