Lynch Recording Rack — User Guide Version 0.2.3 LYNCH AUDIO LAB • RECORDING RACK QUICK START Insert this Audio Unit as an audio effect, for example after Lynch Thirty or another amplifier. Init opens the recording chain ON with gentle desk, EQ, compression and tape settings. Click Recording Rack OFF to compare with the latency-compensated dry signal. Select a module card to reveal its settings. Enable Delay, Reverb or Noise separately when wanted. Input Calibration is the level into the processing chain; Output Trim sets the listening level afterward. Begin with conservative levels and compare with the complete rack bypassed. CONTROLS Drag knobs vertically; Shift makes fine adjustments. Sliders follow the pointer. Mouse wheel and keyboard arrows also edit values. Home/End reach the ends of the range. Double-click or right-click Reset to Default restores one parameter. Simply hovering does not change audio. Click ? to enable per-control explanations. Inactive controls are dimmed and their values retained. All sound controls are Audio Unit parameters. Use Logic's automation lanes, or Logic Pro > Control Surfaces > Controller Assignments to assign MIDI hardware. This audio-effect AU does not advertise an internal MIDI Learn receiver. SOUNDS Starting Points selects complete factory sounds. The arrows move through them. Factory changes retain Input Calibration and Output Trim, except Init which resets everything. Save writes a complete User sound; User opens one for this product. A sound file for another product is rejected. User sounds restore the saved trims too. RECORDING RACK This standalone recording chain can follow an amplifier plugin or process another audio track. It contains no amplifier or cabinet. The complete rack is ON in Init with gentle settings. Turn Recording Rack OFF to bypass its processing while retaining every module setting. Module switches retain their settings while bypassed. Seven module cards keep the principal controls visible. Select a module title for its detailed controls below; the enable switches and main controls stay accessible. Signal order is Desk, EQ, Compressor, Tape, optional Noise, then parallel Delay and Reverb returns. Desk, EQ, Compressor and Tape are prepared with gentle settings; Noise, Delay and Reverb start off. Output Trim remains last. This is a recording chain, not a claim of a physical effects loop inside the original amplifier. Desk selects Tube or Transistor color. Drive controls coloration and Trim sets the level into the following stages. EQ has high/low-pass filters, low and high shelves, and a mid bell with adjustable Q. This EQ is independent of any upstream amplifier tone controls. Compressor selects Opto, VCA or FET response. Threshold and Ratio set the amount, Attack and Release set recovery behavior, and Makeup sets the output level manually. Compression Mix blends the compressed and dry signals. The gain-reduction bar and number show actual compression, not input level. Opto uses adaptive release influenced by the Release setting. Tape selects Studio Reel or Cassette. Drive, Tone, Bias, Wow and Wear have separate controls. Speed changes with tape type: reel uses 7.5, 15 or 30 ips; cassette uses 0.9375, 1.875 or 3.75 ips. Wear changes the tape response independently of the optional noise switch. Noise is input-armed and has a separate Noise Floor; switching it off removes that added noise. Delay and Reverb are parallel sends: Send sets how much dry signal enters each effect, Return sets its level alongside the dry signal, and each return has its own high/low-pass filters. They do not replace the dry path. Delay filtering also applies to its feedback, so repeats inherit the filtering. The reverb low-pass also informs its internal high-frequency damping. Delay offers free time or tempo sync, division and feedback. Mode selects Classic, Stereo, Ping Pong, Dual Rhythm (3:2), or Multi Tap. Stereo creates different repeat timing on the left and right; Ping Pong alternates sides; Dual Rhythm combines two related rhythmic times; Multi Tap creates a pattern of repeats. Width adjusts the stereo spread of the wet return without changing the dry path. Width is also available in Classic; Classic at 100% preserves the earlier delay behavior. The new modes combine both delay sides for mono output; Classic keeps its original mono behavior. Stereo width is heard only with stereo output. New Init settings use Stereo at full width; older saved states and user presets retain the earlier Classic behavior. Reverb offers Plate, Spring and Room with Decay. These are original algorithmic effects, not sampled rooms or captured hardware. LEVELS AND LIMITS All sound controls support host automation. There is no hidden automatic loudness matching: use Desk Trim, Compressor Makeup, effect Return levels and final Output Trim for deliberate gain staging. The complete rack bypass preserves settings. The host receives a fixed latency for consistent timing when changing modules; leave host latency compensation enabled. These are original algorithmic studio effects informed by analog processing principles. They are not measured captures, licensed impulse responses or a promise of exact equivalence to a particular console, compressor or tape machine. Musical listening remains part of selecting the right settings for a track. UI AND GUIDE UI Size offers six sizes and fits within the display. The guide is integrated into this window: Close or Escape returns to the controls. It does not open behind Logic.