LYNCH DISTORTION Eight circuits. One creative destruction machine. GET STARTED Choose a Starting Point from the sound menu. The arrows browse factory sounds; Save stores your own settings and User opens them again. Init restores every parameter to a neutral starting state with the processing modules off and unity gain. Its audio is aligned to the plugin's reported latency. Click a circuit button to choose AND enable its distortion stage. Turn Distortion enabled off to compare it with the same filter, EQ, gate and final limiter settings. Each section has its own clear ON/OFF switch. Dimmed controls keep their settings but their section is inactive. Simply moving the pointer never changes the sound. THE MAIN SIX Drive increases the level entering the selected distortion circuit, up to 48 dB. An internal drive-related trim keeps it more manageable, but does not promise constant perceived loudness. Start lower and bring it up by ear. Character changes the algorithm's character: knee, memory, fold depth or digital grain, depending on the circuit. Tone applies a high shelf within the main distortion stage. Turn it down for darker edges or up for more bite. Bias changes the stage's asymmetry and harmonic balance. Generated DC is removed in the nonlinear path. Dynamic Drive responds to the incoming envelope. Positive values push louder notes harder; negative values soften their drive. Zero is static. This is a performance-sensitive distortion control, not a replacement for the input gate. Wet Mix blends the processed path with the aligned dry path. The input trim, polarity and gate precede both paths. The final limiter comes after this mix. EIGHT ORIGINAL CIRCUITS Smooth: rounded, continuously variable soft saturation. Transistor: asymmetric junction-style clipping with charge recovery and harder edges. Tube: two asymmetric nonlinear stages with a slow bias/sag response. Tape: stateful magnetic-memory coloration, emphasis and high-frequency loss. Fuzz: a crossover dead zone feeding a steep, dense saturation knee. Foldback: bounded waveform folding that adds angular, non-monotonic harmonics. Crush: deliberate sample-hold and bit-depth texture. Chaos: input-driven feedback folding with unstable edges and a decaying silent state. These are original digital algorithms inspired by families of analogue and digital behavior. They are not measured recreations of named hardware. The separate Destruction stage can be stacked with any of them, or used with the main distortion switched off. GATE The linked stereo input gate controls both sides together and acts before the dry/wet split. Threshold decides when it opens. Attack governs the opening, Hold keeps it open through a short gap, and Release controls the return to attenuation. Range limits how deep the attenuation can become. Use a smaller range for a gentler result or a larger one for near-silence between notes. Gate GR shows its actual envelope attenuation. The separate Drive Activity meter shows a held, level-dependent indication of how much the main distortion changes the signal. Its percentage is neither a THD measurement nor gain reduction. Gate and Drive Activity read zero and dim when their stage is off or the plugin is bypassed, even while the host transport is stopped. FILTERS The high-pass and low-pass filters each have an independent switch, cutoff and resonance. Use both to isolate a band. Both cutoffs run from 20 Hz to 20 kHz; the usable spectrum still follows the audio sample rate. Resonance around 0.71 is a smooth starting point. High resonance emphasizes the cutoff region and may push later stages harder. Filter Position moves both filters before or after the distortion and destruction stages. Pre can remove sub-bass before clipping or focus the frequencies that drive it. Post can remove fizz and sculpt the generated harmonics. Filter switches and placement are automated independently. EQ The post-processing EQ has a bass shelf centered around 130 Hz, a treble shelf around 6.5 kHz, and a tunable midrange. Mid Frequency selects the target; Mid Resonance controls its Q. Higher Q means a narrower boost or cut. These controls follow the distortion, destruction and selected filter routing. DESTRUCTION This is an independent second damage stage. Resolution reduces the effective amplitude resolution. Lower values create more obvious steps; 24 bits is the clean endpoint. Sample Rate adds sample-hold reduction. Full Rate disables that additional rate reduction; it does not change the DAW's sample rate. Wave Fold bends the waveform back on itself, making complex, angular harmonics. Voltage Starve adds a dead zone and level collapse. At high settings it can deliberately choke or almost silence a quiet source. That behavior is part of the effect. Crush, Chaos, folding and deliberate rate reduction can generate strong digital artifacts. Oversampling reduces unwanted nonlinear aliasing, but these modes intentionally create abrasive spectra and are not advertised as alias-free. ROUTING Input sets the gain entering the gate and processing chain. The Input meter is taken before this trim. Stereo Width changes the mid/side balance of the wet path: 0% is mono and 100% is unchanged. It does not synthesize stereo from a mono source. Check very wide material in mono. Polarity Invert reverses polarity before the processing and dry/wet split. Signal flow: Input and Polarity -> Gate -> Pre Filters when selected -> Distortion -> Destruction -> Post Filters when selected -> EQ -> Stereo Width -> aligned Wet/Dry Mix -> Output -> Limiter Push -> final Limiter and Sample Guard. FINAL LIMITER The final strip stays visible at the bottom. Enable it independently of the distortion stages. Push drives the limiter harder. Ceiling sets the final sample-peak ceiling in dBFS. Release changes its gain recovery time. Output is a trim BEFORE this limiter, so the enabled ceiling still applies after the output gain and wet/dry mixture. The scrolling graph shows measured limiter gain reduction over approximately five active seconds. When the limiter is off or the plugin is bypassed, its current reading says OFF and its historical trace is dimmed and paused. The top line is 0 dB and the bottom line is 24 dB; the numerical reading still displays deeper reduction. Sample Guard shows any residual sample-peak protection separately. Input and Output show RMS level; Output Peak shows the peak envelope. The ceiling applies while Limiter is on and Bypass is off. It is a sample-peak ceiling, not a certified true-peak/dBTP measurement or guarantee. The distortion amount and perceived loudness may still change substantially with a preset or drive adjustment. BYPASS AND LATENCY Bypass returns the original input with matching latency and excludes every processing stage, including the limiter. A hot bypass signal can therefore exceed the limiter ceiling. The reported latency is fixed at 608 samples, including nonlinear processing alignment and lookahead. The host uses it for plugin delay compensation. Limiter off does not remove that alignment delay. The nonlinear path uses 8x oversampling at 44.1/48 kHz and 4x at 88.2/96/192 kHz. The processing-rate choice follows sample rate, not a changing quality switch. Sample rate, buffer size and CPU load still affect the available instance count. CONTROL, AUTOMATION AND HELP Every sound parameter is exposed to the host's automation system. Click and drag dials; Shift makes their movement finer. Scroll adjusts a control under the pointer. Double-click a dial or right-click and choose Reset to Default to restore its default. A circuit button selects the circuit and enables Distortion as one user action. Automating only Distortion circuit from the host leaves Distortion enabled unchanged; automate both if needed. Section switches keep their stored settings while off. For a hardware controller in Logic, use Logic's Controller Assignments or Smart Controls to map the exposed parameters. This plugin does not claim a separate internal MIDI Learn system. The right-click assignment item opens this guide. ? Help turns on contextual explanations. Guide opens this text inside the plugin, above its controls, and Escape closes it. UI Size scales the whole interface and caps it to fit the current screen. The host controls the outside window frame. USER SOUNDS Save writes a named .lynchdistortion sound with all 41 parameter values. User lists saved sounds and can open a file from another folder. Factory sounds and your saved files are separate. The default user folder is Application Support/Lynch Audio Lab/Distortion/Presets. Project state is saved through the host separately. PRIVATE BUILD This is a private development effect build. Technical test results are separate from listening, musical preference, and claims of hardware equivalence. Use your ears to choose the amount of damage that serves the track.