NEW: SMOOTH AND DECIBEL DEPTH Use the selector above the large knob to choose Amount (%) or Reduction (dB). In dB mode, the knob sets peak attenuation per accepted kick from 0 to 40 dB. The inactive depth value is retained. 0% Amount or 0 dB Reduction is neutral. Smooth rounds the dip entry and recovery inside Length. 0% keeps the original response; higher values give a softer onset and return. It adds no latency and does not extend the accepted kick or Trigger Solo window. Old six-control presets load with the original Amount mode and Smooth at zero. LYNCH AUDIO LAB / KICK DUCKER Private 0.1.1 / Build 2 MAKE ROOM FOR THE KICK Insert Kick Ducker on the bass, synth, pads, music bus or other track you want to lower. In Logic's Side Chain menu at the top of the plugin window, select the kick track or a drum bus. Play the source and receiving tracks together. Raise Amount. Init starts at zero, so loading it does not change your sound. This is an audio effect, not a MIDI effect or a tempo-only pumper. A separate kick send is the most dependable trigger. Kick Ducker can also look for kick-like attacks in a full drum loop using its low-frequency bias. It does not isolate instruments with AI and cannot promise perfect kick recognition in every mix. Low toms, bass notes and bleed can trigger it; strong cymbals can mask a kick. If tuning cannot distinguish a source, use a dedicated kick send. No sidechain audio is added to the main output unless you deliberately switch on Trigger Solo. AMOUNT The large control sets the peak attenuation per accepted hit, from no ducking to 40 dB at 100%. Every accepted hit starts a shaped, fixed-length reduction. The detector follows kick-like attacks; it does not keep the track suppressed simply because the source kick has a long ringing body. LENGTH The total duration in milliseconds from detection to complete recovery, 5–300 ms. A fast rounded attack and a smooth return are set automatically. Short settings open a small pocket for the transient; longer settings pump the music. Attack is at most 1 ms and is limited further for very short dips. There is a small plateau before the smooth return for longer lengths. A new hit waits at least 60 ms or Length, whichever is longer, to avoid tail retriggering and overlapping dips. Very rapid rolls may need a shorter Length. This product intentionally omits separate Attack, Release, Hold and Min Gap. Length and Amount changes shape the next accepted hit; the active envelope finishes smoothly. Setting Amount to zero or Bypass fades ducking out in 5 ms. SENSITIVITY Raise to detect quieter kicks. Lower if unrelated quiet material is triggering. This adjusts the minimum trigger level, not monitor loudness or ducking depth. It cannot distinguish two instruments with nearly identical low-frequency content. Start at 50% and use the reduction graph while the source plays. KICK FOCUS Sets the analysis band's upper cutoff, 60–300 Hz, with a fixed 25 Hz high-pass. Lower favors deep bass drums; higher includes short and brighter kicks. The engine compares this band to the full sidechain at a fixed moderate selectivity. Kick Focus changes only detection and Trigger Solo, never the frequency balance of the receiving track. There is no EQ in the main path. TRIGGER SOLO Mutes the receiving track and opens the signed analysis band only for Length after each accepted kick. At 20 ms, only those 20 ms pass, then silence. Very short rounded edges prevent hard cuts and stay inside the selected window. Length is latched at detection; changing it cannot stretch the current window. There is no normalization or added gain, so deep or quiet kicks can sound low. The audio is the analysis band inside accepted windows, not a separated kick stem or a beep. Rejected hits and the remaining kick tail are muted. Use the gain-reduction graph with Amount above zero to see accepted duck pulses. You can listen even with Amount at zero; no reduction will then be drawn. A missing sidechain gives silence in Solo. Bypass overrides Solo and restores the receiving track. Turn Solo off when finished. Solo is saved in presets and host state, and its ON button is illuminated so an active monitor is visible. SIDECHAIN AND METER The status reports the actual connection and signal in the host. If it says NOT CONNECTED, select a source in the host Side Chain menu. CONNECTED / QUIET means a connection exists but the measured trigger is below the meter's floor. The scrolling graph and dB reading show actual main-track gain reduction, including when Solo is active. Stereo sidechains are linked without summing for detection; opposite polarities cannot cancel a kick trigger. Solo preserves stereo polarity, duplicates mono to stereo, and averages stereo for mono output. A phase-inverted stereo source may therefore cancel in mono Solo while still triggering ducking. Missing/error sidechain returns the main track dry in 5 ms. PRESETS, AUTOMATION AND HELP Five factory starting points: Init, Tight / Transient Space, Smooth / Bass Pocket, Deep / Electronic Pump and Long / Atmosphere. The arrows browse them. Save stores your own settings; User loads them. These files are separate from Ducker presets because this plugin has its own six-parameter product contract. The host saves the complete instance. All six controls support host automation; continuous controls are smoothed. Use Logic Controller Assignments for hardware control. No independent MIDI input or MIDI Learn is implemented here. Double-click a continuous control to restore its default, Shift-drag for fine changes, and scroll over it to adjust. Hover alone never changes a setting. ? Help enables explanations for each control. Guide opens inside this editor; Close or Escape returns to the controls. UI Size scales the complete interface. TECHNICAL SCOPE Mono, mono-to-stereo and stereo Audio Unit on Apple Silicon macOS, with mono or stereo external sidechain. Zero added audio latency and no generated tail. The causal detector still needs incoming evidence: detection can be several milliseconds after a kick starts. It cannot duck before an unknown transient. No compressor makeup gain, saturation, limiter, EQ or automatic level matching is applied to the receiving track. This is deliberately a clean volume duck. The engine reuses the pinned Ducker 0.2.1 core with a fixed Kick Pulse policy. Automated DSP/native host/UI/AU checks are documented separately. Passing them does not guarantee musical preference or perfect recognition of every drum mix.