LYNCH BROKE EQ — USER GUIDE 0.4.0 INIT AND PRESET READABILITY Init resets to a clean starting sound. Factory IDs and saved presets are unchanged. The preset control uses the light Broke appearance, including in a dark host. Use Save/User or your host project to save the initialized sound. TUBE LIMITER An independent ON/OFF peak stage at the end of the active chain, after Color, EQ or compression, Mix and Output. Available in every Character. Amount 0–100% adds up to 12 dB of drive and progressively stronger modeled tube color. Start around 20–35%, then increase until the peaks and texture suit the music. It does not match RMS, LUFS or average loudness; Output remains your manual trim before the limiter. The original tube-inspired asymmetric saturation uses antiderivative antialiasing, DC removal and a linked stereo peak detector. A soft knee, instant peak attack, short hold and program-dependent release round peaks. The fixed ceiling is -1 dBFS for sample peaks after the ON fade has settled. It is not a true-peak or loudness-target limiter. There is no added lookahead or latency; the plugin remains at 16 samples. ON/OFF and Amount changes glide to avoid hard switching. Global Bypass returns the original latency-aligned input, regardless of the limiter. GAIN REDUCTION shows actual limiter attenuation, excluding its input drive and saturation. The graph records the largest attenuation in each 50 ms interval for four seconds; downward dips show attenuation and the scale expands above 6 dB. The number shows current limiter reduction. In Compressor this is separate from the original compressor GR readout. OFF or global Bypass stops new limiter reduction; the graph retains and scrolls the recent history. Both controls support host automation, saved projects, Save/User presets, and Amount supports drag, scroll, Shift-fine and Hover. Init and factory Starting Points turn the limiter OFF, with Amount at 35%. Older states also load limiter OFF rather than accidentally enabling it. Auto Gain has been removed from the sound and editor; its retired host parameter stays reserved and inert so old automation does not control the new limiter. FIVE CHARACTERS Desk / Warm / Tape / Worn / Tube Drive Tube Drive adds inherent biased soft saturation plus its own shelf voicing. Color increases saturation. The High Pass and Low Pass controls remain available. An original vintage-inspired effect with the simple Broke feel: cream, charcoal, rust and warm sound. Five Character buttons and 16 Starting Points. No commercial hardware emulation or third-party audio library. Low and High are broad shelves, each +/-12 dB. Mid is a broad bell, +/-12 dB; Focus moves its center from 250 Hz to 4 kHz. Desk: 110 Hz / 6.5 kHz shelves; Warm: 160 Hz / 4.8 kHz; Tape: 90 Hz / 8 kHz; Worn: 240 Hz / 3.6 kHz. Frequencies are limited at low sample rates. Color adds independent warmth. Flat gains, filters Off and Color 0 with Tube Limiter OFF give latency-aligned unity. EQ has no wet/dry Mix: the third large control is High. High Pass and Low Pass are two thin logarithmic frequency sliders with smooth changes and 12 dB/oct slopes. High Pass: far left is Off, then 20 Hz to 2 kHz; cuts the low end. Low Pass: 200 Hz to 20 kHz, with Off at far right; cuts the high end. At low sample rates the effective cutoff is capped at 45% of sample rate. Both follow the tone EQ and Color. Combine them for a narrower band, or cross the frequencies for strong attenuation. Both are Off in all factory starting points and when loading older eight-parameter presets. Double-click or right-click Reset to Default returns a filter to Off. Values display Hz or kHz. Color: compensated four-times oversampled soft saturation, gentle high-frequency softening and character-dependent warmth. Zero retains clean color; higher settings create audible texture. It is modeled color rather than actual tape/tube circuitry. Output: -36 to +6 dB; watch the peak meter and leave headroom. Bypass passes latency-aligned input at unity. Starting Points selects a curated setup. The arrows browse them. Save writes a standard .aupreset file; User loads a preset from this exact plugin. Current settings are also recalled with the host project. Character changes its voicing without replacing your knob values. Hover is off initially. Enable it for click-free control of the main dials and the Limiter Amount knob. Move within the control bounds to reach its full range; Escape disables Hover. Drag or scroll normally; Shift gives finer control. Right-click provides Reset to Default and Automation / MIDI assignment help. All twelve active sound parameters support host automation. Use Logic's Controller Assignments for MIDI control; internal MIDI Learn is not included. ? enables the help reminder; each control includes an English tooltip. UI Size offers 75–150%, limited by available display area. The host owns the outer window. Supported sample rates: 8–192 kHz; mono-to-mono, mono-to-stereo and stereo-to-stereo. Apple Silicon native AUv2 private test build. Fixed reported 16-sample latency. No render-time file access or allocation. Input/output headroom and musical taste still matter. Technical validation does not replace listening in a real session. HOST COMPATIBILITY 13 host parameters: stable existing IDs, retired Auto Gain ID10, Tube Limiter ID11, Limiter Amount ID12. No old IDs were reused. GUIDE WINDOW Guide opens a scrollable reading panel inside the plugin, in front of the controls and at the current UI scale. Close or Escape returns to your sound without changing any settings. Select and copy guide text if needed. Hover Control pauses while the guide covers the knobs and resumes after closing; its ON/OFF preference stays.