MATCH — ONE SHOT (2026-10-11) Manual Output is the default. Click Match and play five seconds of representative audio. It measures the entire audible chain, then sets Output once. The trim stays fixed until you change Output or click Match again. Nothing keeps following your playing. Maximum correction is ±12 dB per click, within the Output range. The button shows Cancel Match during capture; click to cancel. Parameter edits, reset, bypass and closing the editor cancel. Insufficient audio times out after 20 seconds. RMS comparison is not guaranteed equal perceived loudness. Vocal Strip and Broken Amp require 100% Wet during capture; set your desired blend afterwards. Master/Analog Strip require Stereo monitoring and the Output module on. The final limiter remains after Output and can constrain level matching. Match is independent of Master Assist / Fit Target; verify the full song after any Output change. Thirty Old Version retains its own manual Old Output and does not run Match. The host parameter "Level Match (Legacy)" is retained for old state IDs but is inactive. Previous descriptions of continuous Level Match below are historical and superseded by this section. LYNCH MASTER STRIP — USER GUIDE0.2.0 Logic: Audio FX > Audio Units > Lynch Audio Lab > Master Strip. Insert on the master/mix bus. Start with Clean Start, then shape the music. Tone shapes broad balance. Surgical has two aligned rows: Body Frequency/Gain/Q and Presence Frequency/Gain/Q. Dynamic tames broad moving low/high energy; Glue controls linked compression; Colour provides independent Tape, Tube and Grit; Punch changes attack/sustain; Stereo sets width and mono bass. Input stays upstream; final output and LUFS/true-peak/limiter meters sit at the bottom. MEASURED ASSIST Select a genre/instrument profile and press Analyze. Play representative input; the status shows useful material time separately from elapsed time. At least 8 useful seconds are required. Silence does not count as representative audio. Analyze remains lit only while capture is actually running. Suggest stops an active capture, waits for the engine, then displays the proposed tone/dynamics values. Review them and press Apply to audition. Assist is conservative signal analysis, not a style classifier or a guarantee of a finished mix. Input analysis precedes processing; the dynamics proposal accounts for Input trim. Warnings flag quiet, hot/clipped or problematic phase material. Changes after a suggestion invalidate it rather than applying a stale snapshot. Choose Suggest again after editing. Hear Before / Hear After compares only the parameters changed by Assist. Undo restores only those changes and preserves unrelated Input, Output, monitoring and delivery settings. Conflicting edits or a new state/starting point invalidate this temporary transaction. Capture/proposal/comparison history belongs to the editor session; actual audio settings save in the AU state. TARGETS AND FINAL MEASUREMENT The bottom output section contains final limiting controls and output meters. Spotify is a -14 integrated LUFS / -1dBTP reference. Loud (-11LUFS / -2dBTP) and Dynamic (-16LUFS / -1dBTP) are creative references. These buttons select Target, Ceiling and Limiter On; selecting one does not instantly normalize the song. Custom indicates that the current Target/Ceiling differ from those references. For Fit Target: use Stereo monitoring, Bypass Off, Level Match Off and Limiter On. Select a reference, then play the complete song from the beginning at its final settings. The output status explains whether the measurement is current, settling or unsuitable. Processing/monitor/target changes invalidate old output history; pending reset commands must be acknowledged by audio before fitting. Fit Target enables after8 useful seconds for workflow checks, but a complete song measurement is required for delivery. It adjusts limiter Drive by the measured difference, bounded to±12dB per action and the Drive range. Replay the entire song after every fit, then check integrated loudness, true peak and gain reduction. Limiting is nonlinear, so a fit can require another measured pass. Fit Target and Reset Meter are momentary actions; selected references stay marked. Reset Meter starts fresh output history and does not stop input Analyze. Exported files can change through later processing, faders or encoding; measure the exported deliverable too. The meter/limiter are not externally certified. CONTROLS AND HELP Click a module to inspect it. Double-click its heading to enable or bypass it; the ON/OFF badge shows the actual state. Drag a dial to adjust it, hold Shift for fine adjustment, scroll for small changes and double-click to reset its default. These strips have no click-free hover adjustment. The ? button enables descriptions without changing any sound values. Guide opens inside the plugin, above the controls; Close or Escape returns to editing. UI Size scales the whole editor from75–150%, capped to the available screen. All audio controls support host automation. In Logic, use Controller Assignments Learn to bind a hardware controller. The parameter context menu explains the host workflow. Save complete settings using Logic's plugin preset menu. LATENCY AND SIGNAL PATH Colour processing retains4x oversampling and32 samples of latency. The final linked limiter adds5ms lookahead plus48 reconstruction samples. Bypass remains time aligned and intentionally bypasses peak protection. Colour Mix precedes the limiter. Level Match is slow RMS comparison in the colour chain, not final LUFS normalization. Tape/Tube are original artistic models, not verified named hardware emulations. Numerical checks and musical listening are separate.