LYNCH RUMBLE · USER GUIDE QUICK START — DIRECT / INSERT Insert Rumble on an isolated kick track. Leave Routing on Direct / Insert and choose Concrete Starter. Play your kick, then set Rumble, Decay and Pump. The dry kick has its own level and never passes through the wet distortion or filters. Output and Protect affect the combined signal. Zero added latency. QUICK START — SEND / BUS Send the kick to an aux and insert Rumble on that aux. Select Send / Bus · Wet Only. Keep the original kick track playing. The return contains only rumble, and uses its incoming kick as the ducking trigger: no separate sidechain route is needed. The routing choice survives factory and User preset changes. Use Direct / Insert on a kick group if you want its original kick bus audio preserved. Our Bypass control passes the original signal in Direct mode and mutes the return in Send mode. A host's hard bypass can skip plugin processing entirely and pass the kick through an aux; mute the aux rather than hard-bypassing it if that happens. Dry Kick and Wet Solo are inactive in Send mode. WHAT MAKES THE RUMBLE Kick → adaptive wet feed → rhythmic repeats → diffusion/reverb → four-times-processed color → low/high cuts → centered sub / stereo air → kick carve → ducking → wet amount. Chamber is tight, Concrete is dense and Tunnel is broad. The decay is measured to -60 dB, not a musical note length. Motion puts rhythmic repeats into the reverb feed. No sample pack, convolution IR or copied commercial effect is used. DUAL ECHO — 1/8 + 1/16 Open ECHO and switch on 1/8 Echo, 1/16 Echo or both. Each lane has its own Level, Feedback, Duck and Recovery. The straight note lengths follow host tempo with Tempo Sync on; Manual BPM is used otherwise or when no host tempo is available. Recovery is a percentage of that lane's note length: 100% takes one echo interval after Hold. Hold, Curve, Trigger Mode and Threshold are shared, so both lanes listen to the same incoming kick but duck independently. Space Pump controls only the reverb and Sub Body. The duck meter shows the greatest active reduction. The echoes run in parallel with the space. Color, Low Cut, High Cut, Resonance and Kick Carve also process them. Their low-frequency returns are centered. Rumble controls the combined wet layer. Set Space Level to zero on SPACE for echo-only rumble; use Space Level to blend the reverb back in. Motion / Echo Beat on SPACE still feed the original reverb network. Example: 1/8 Level 65%, Duck 85%, Recovery 75%; 1/16 Level 45%, Duck 65%, Recovery 75%. Increase Feedback for longer rolling tails. Existing factory and old User sounds start with both new echoes off. PUMP Auto Kick detects incoming transients above Trigger Threshold and pushes the rumble down. Hold keeps it out of the impact. Recovery and Curve control its return. Tempo Sync uses host tempo; Recovery Beat sets the duration. Without Sync, Recovery uses milliseconds. Envelope mode ducks continuously from input level, useful for long 808s. Auto Feed adapts only the wet feed, with gain bounded from -12 to +24 dB. Manual BPM is the fallback when the host supplies none, and sets Motion timing with Sync off. For very quiet kicks lower Trigger Threshold or raise Input. For already reverberant kicks or noisy recordings, adjust Threshold, Hold and Recovery; Envelope may be more reliable. Auto Kick has a 120 ms minimum trigger gap to reject body ringing. For very rapid double hits or rolls use Envelope mode. This plugin does not separate a kick from an entire mix. Kick timbre, tuning and available headroom still matter. TONE / SUB Low Cut removes infrasonic energy. High Cut makes the bass rumble deep or exposes industrial grit. Kick Carve cuts a wet band near Sub Tune so the original body has space. Sub Body is an optional kick-triggered decaying sine for thin kicks. Sub Tune is manual; it does not claim automatic pitch detection. Set Sub Body to zero for a purely processed kick tail. Width affects the side channel above Mono Below; keep sub energy centered. COLOR Drive, Tube, Tape and Grit process only the rumble. These are original saturation algorithms, not measured hardware models. Processing the color stage at four times the sample rate reduces abrupt nonlinear artifacts, but extreme drive can still produce aliases. Protect is a final sample ceiling, not a lookahead or true-peak limiter. Leave output headroom for your mix. CONTROLS / AUTOMATION Drag wheels vertically, Shift for fine changes. Scroll works without holding the mouse. Double-click a control to reset it. Hover Control is opt-in; entering a wheel does not jump the value. Top/bottom reach the full range within its bounds. Exit, focus loss and Escape finish gestures. UI Size scales 75–150%, limited by the screen; your host owns the outer window. All 49 parameters, including Routing, expose standard AU automation. Record mouse edits with Logic Touch/Latch. For a hardware knob use Logic's Controller Assignments and Learn on the selected plugin parameter. This AU effect does not expose its own MIDI input/learn port. PRESETS 24 factory starting points range from clean sub to harsh industrial. Arrows move through them. Init · Dry Kick removes the wet layer. Save stores your current sound in a .lynchrumble file; User… loads saved sounds or opens an existing file. Routing stays as chosen in the current instance when loading a sound. Project state restores every parameter, including Routing. Your user sounds are never replaced by an update. IF YOU HEAR NO CHANGE Play the kick repeatedly. Check Bypass, Rumble and the wet meter. Turn Wet Solo on in Direct mode to hear the tail. If the trigger count is still, lower Threshold. Check Tempo Sync/Recovery, Output and your aux routing. A silent input after reset remains silent. Large Decay settings retain tails until they decay or the host resets the plugin. PRIVATE TEST RELEASE Native AUv2 on Apple Silicon macOS. Technical engine/AU/UI checks and preview renders do not prove musical quality for every kick. Audition with your own kicks in Logic. Other Lynch plugins and the open production are preserved.